[Jan 26, 2023] Fortinet Dumps - Learn How To Deal With The (NSE6_FWF-6.4) Exam Anxiety
DEMO FREE BEFORE YOU BUY NSE6_FWF-6.4 DUMPS
NEW QUESTION 11
Refer to the exhibit.
If the signal is set to -68 dB on the FortiPlanner site survey reading, which statement is correct regarding the coverage area?
- A. Areas with the signal strength weaker than -68 dB are cut out of the map
- B. Areas with the signal strength equal or stronger than -68 dB are highlighted in multicolor
- C. Areas with the signal strength equal to -68 dB are zoomed in to provide better visibility
- D. Areas with the signal strength weaker than -68 dB are highlighted in orange and red to indicate that no signal was propagated by the APs.
Answer: B
NEW QUESTION 12
You are investigating a wireless performance issue and you are trying to audit the neighboring APs in the PF environment. You review the Rogue APs widget on the GUI but it is empty, despite the known presence of other APs.
Which configuration change will allow neighboring APs to be successfully detected?
- A. Enable Radio resource provisioning on the relevant AP profiles.
- B. Enable Locate WiFi clients when not connected in the relevant AP profiles.
- C. Ensure that all allowed channels are enabled for the AP radios.
- D. Enable Monitor channel utilization on the relevant AP profiles.
Answer: A
Explanation:
The ARRP (Automatic Radio Resource Provisioning) profile improves upon DARRP (Distributed Automatic Radio Resource Provisioning) by allowing more factors to be considered to optimize channel selection among FortiAPs. DARRP uses the neighbor APs channels and signal strength collected from the background scan for channel selection.
NEW QUESTION 13
Where in the controller interface can you find a wireless client's upstream and downstream link rates?
- A. On the controller CLI, using the WiFi Client monitor
- B. On the AP CLI, using the cw_diag ksta command
- C. On the AP CLI, using the cw_diag -d sta command
- D. On the controller CLI, using the diag wireless-controller wlac -d sta command
Answer: D
NEW QUESTION 14
When using FortiPresence as a captive portal, which two types of public authentication services can be used to access guest Wi-Fi? (Choose two.)
- A. Short message service authentication
- B. Software security token authentication
- C. Social networks authentication
- D. Hardware security token authentication
Answer: A,C
NEW QUESTION 15
Which two statements about background rogue scanning are correct? (Choose two.)
- A. A dedicated radio configured for background scanning can support the connection of wireless clients
- B. Background rogue scanning requires DARRP to be enabled on the AP instance
- C. A dedicated radio configured for background scanning can detect rogue devices on all other channels in its configured frequency band
- D. When detecting rogue APs, a dedicated radio configured for background scanning can suppress the rogue AP
Answer: A,D
Explanation:
To enable rogue AP scanning
NEW QUESTION 16
Part of the location service registration process is to link FortiAPs in FortiPresence.
Which two management services can configure the discovered AP registration information from the FortiPresence cloud? (Choose two.)
- A. FortiAP Cloud
- B. FortiSwitch
- C. AP Manager
- D. FortiGate
Answer: A,D
Explanation:
FortiGate, FortiCloud wireless access points (send visitor data in the form of station reports directly to FortiPresence)
NEW QUESTION 17
Refer to the exhibits.
Exhibit A
Exhibit B
The exhibits show the diagnose debug log of a station connection taken on the controller CLI.
Which security mode is used by the wireless connection?
- A. Open, with radius MAC filtering
- B. WPA2 Personal and radius MAC filtering
- C. WPA2 Enterprise
- D. WPA3 Enterprise
Answer: C
Explanation:
Best security option is WPA2-AES.
NEW QUESTION 18
Which two statements about distributed automatic radio resource provisioning (DARRP) are correct? (Choose two.)
- A. DARRP measurements can be scheduled to occur at specific times.
- B. DARRP requires that wireless intrusion detection (WIDS) be enabled to detect neighboring devices.
- C. DARRP performs measurements of the number of BSSIDs and their signal strength (RSSI). The controller then uses this information to select the optimum channel for the AP.
- D. DARRP performs continuous spectrum analysis to detect sources of interference. It uses this information to allow the AP to select the optimum channel.
Answer: B,D
Explanation:
DARRP (Distributed Automatic Radio Resource Provisioning) technology ensures the wireless infrastructure is always optimized to deliver maximum performance. Fortinet APs enabled with this advanced feature continuously monitor the RF environment for interference, noise and signals from neighboring APs, enabling the FortiGate WLAN Controller to determine the optimal RF power levels for each AP on the network. When a new AP is provisioned, DARRP also ensures that it chooses the optimal channel, without administrator intervention.
NEW QUESTION 19
What is the first discovery method used by FortiAP to locate the FortiGate wireless controller in the default configuration?
- A. Broadcast
- B. Static
- C. DHCP
- D. Multicast
Answer: B
NEW QUESTION 20
Which two roles does FortiPresence analytics assist in generating presence reports? (Choose two.)
- A. Reporting potential threats by guests on site
- B. Gathering details about on site visitors
- C. Predicting the number of guest users visiting on-site
- D. Comparing current data with historical records
Answer: B,C
NEW QUESTION 21
As standard best practice, which configuration should be performed before configuring FortiAPs using a FortiGate wireless controller?
- A. Set the wireless controller country setting
- B. Create a custom AP profile
- C. Create wireless LAN specific policies
- D. Preauthorize APs
Answer: B
NEW QUESTION 22
Which two phases are part of the process to plan a wireless design project? (Choose two.)
- A. Hardware selection phase
- B. Site survey phase
- C. Project information phase
- D. Installation phase
Answer: B,D
Explanation:
Reference:
https://www.automation.com/en-us/articles/2015-2/wireless-device-network-planning-and-design
NEW QUESTION 23
How are wireless clients assigned to a dynamic VLAN configured for hash mode?
- A. Using the current number of wireless clients connected to the SSID and the number of clients allocated to each of the VLANs
- B. Using the current number of wireless clients connected to the SSID and the number of IPs available in the least busy VLAN
- C. Using the current number of wireless clients connected to the SSID and the group the FortiAP is a member of
- D. Using the current number of wireless clients connected to the SSID and the number of VLANs available in the pool
Answer: D
Explanation:
VLAN from the VLAN pool based on a hash of the current number of SSID clients and the number of entries in the VLAN pool.
NEW QUESTION 24
When enabling security fabric on the FortiGate interface to manage FortiAPs, which two types of communication channels are established between FortiGate and FortiAPs? (Choose two.)
- A. Security channels
- B. FortLink channels
- C. Control channels
- D. Data channels
Answer: C,D
Explanation:
The control channel for managing traffic, which is always encrypted by DTLS. l The data channel for carrying client data packets.
NEW QUESTION 25
Refer to the exhibit.
If the signal is set to -68 dB on the FortiPlanner site survey reading, which statement is correct regarding the coverage area?
- A. Areas with the signal strength weaker than -68 dB are cut out of the map
- B. Areas with the signal strength weaker than -68 dB are highlighted in orange and red to indicate that no signal was propagated by the APs.
- C. Areas with the signal strength equal or stronger than -68 dB are highlighted in multicolor
- D. Areas with the signal strength equal to -68 dB are zoomed in to provide better visibility
Answer: B
NEW QUESTION 26
Where in the controller interface can you find a wireless client's upstream and downstream link rates?
- A. On the controller CLI, using the WiFi Client monitor
- B. On the controller CLI, using the diag wireless-controller wlac -d sta command
- C. On the AP CLI, using the cw_diag -d sta command
- D. On the AP CLI, using the cw_diag ksta command
Answer: D
NEW QUESTION 27
Refer to the exhibits.
Exhibit A
Exhibit B
The exhibits show the diagnose debug log of a station connection taken on the controller CLI.
Which security mode is used by the wireless connection?
- A. Open, with radius MAC filtering
- B. WPA2 Personal and radius MAC filtering
- C. WPA2 Enterprise
- D. WPA3 Enterprise
Answer: B
NEW QUESTION 28
......
Latest Fortinet NSE6_FWF-6.4 Dumps with Test Engine and PDF: https://www.vcedumps.com/NSE6_FWF-6.4-examcollection.html
Now, get the NEWEST NSE6_FWF-6.4 dumps in Test Engine from: https://drive.google.com/open?id=1tLPguORga6lsl2Pl636V4y0FCOPwd0Sc
