Unique Top-selling HPE6-A72 Exams - New 2021 HP Pratice Exam
Aruba Certified Switching Associate (ACSA) V1 Dumps HPE6-A72 Exam for Full Questions - Exam Study Guide
NEW QUESTION 16
What is the process where a compute device converts logical data bits into the correct physical representation depending on the media?
- A. Propagation
- B. Encapsulation
- C. Demodulation
- D. Modulation
Answer: B
NEW QUESTION 17
What is an available command on an Aruba AOS-CX switch that would back up the secondary image to a secure remote repository?
- A. copy secondary tftp://[email protected]/GL.10.04.0003.swi
- B. backup secondary sftp://[email protected]/GL.10.04.0003.swi
- C. copy sftp://[email protected]/GL.10.04.0003.swi secondary
- D. copy secondary sftp://[email protected]/GL.10.04.0003.swi
Answer: D
NEW QUESTION 18
Click on the colored box that corresponds with the line that best represents Broadcast traffic flow.
Answer:
Explanation:
NEW QUESTION 19
You need to remote into an AOS-CX switch using SSH in order to update the management IP address for future connections. Unfortunately, you mis-configured the IP address and are now locked out of the switch.
What command could you have issued before making changes that would have recovered the original switch configuration after ten minutes?
- A. checkpoint auto confirm 10
- B. checkpoint rollback 10
- C. boot system secondary 10
- D. checkpoint auto 10
Answer: D
NEW QUESTION 20
Refer to the exhibit.
What VSF command produces the above output?
- A. show vsf member
- B. show vsf detail
- C. show vsf link
- D. show vsf topology
Answer: D
NEW QUESTION 21
Aruba Access Points tunnel traffic in a campus to the Mobility Controller using which protocol?
- A. Lightweight Access Point Protocol (LWAPP)
- B. Process Application Programming Interface (PAPI)
- C. Generic Routing Encapsulation (GRE)
- D. Control and Provisioning of Wireless Access Points (CAPWAP)
Answer: C
NEW QUESTION 22
Which two statements are true regarding Checkpoints on Aruba switches? (Choose two.)
- A. Stacking switches using VSF or VSX will disable the Checkpoint feature.
- B. System-generated checkpoints are created after a configuration change and 5 minutes of inactivity.
- C. A checkpoint is a snapshot of the running-configuration and relevant metadata at the time the checkpoint was created.
- D. Rolling back to a prior checkpoint triggers a reboot of the switch.
- E. Checkpoints are available on AOS 5400R switches, as well as on all AOS-CX switches.
Answer: C,E
NEW QUESTION 23
Interface 1/1/1 is up
Admin state is up
Link transitions: 1
Description: TO_PC-1
Hardware: Ethernet, MAC Address: 00:11:22:33:44:55
MTU 1500
Type 1GbT
Full-duplex
qos trust none
Speed 1000 Mb/s
Auto-negotiation is on
Flow-control: off
Error-control: off
MDI mode: MDIX
VLAN Mode: access
Access VLAN: 1111
Which command will produce the above output?
- A. show interface gigabit 1/1/1
- B. show vlan 1111
- C. show interface vlan 1111
- D. show interface 1/1/1
Answer: D
NEW QUESTION 24
What is a benefit of choosing a 3-Tier design with routing at the Aggregation layer?
- A. Connecting WAN/MPLS and Data center access to the Aggregation layer
- B. Shifting endpoint access to the Aggregation layer from the Access layer
- C. Better Core router performance by offloading processing
- D. Using access control lists (ACLs) at the Core to improve performance
Answer: C
NEW QUESTION 25
Match each description to the correct term.
Answer:
Explanation:
NEW QUESTION 26
Refer to the exhibit.
All four switches in the diagram have been configured with the region name "Aruba1".
What two other MSTP configurations must match for switches within the same MST region? (Choose two.)
- A. MST VLAN to instance mapping
- B. MST version number
- C. MST revision number
- D. MST region type
- E. MST Bridge ID
Answer: A,C
NEW QUESTION 27
Place the OSI Layers in the correct order. Arrange them from least to greatest, starting with Layer 1 on the top, and progressing to Layer 7 on the bottom.
Answer:
Explanation:
1 - physical Layer
2 - Data Link Layer
3 - Network Layer
4 - Transport Layer
5 - Session Layer
6 - Presentation Layer
7 - Application Layer
NEW QUESTION 28
What is the correct description of a Multi-Layer Switch?
- A. a switch with Layer 3 routing capabilities but lacks any Layer 1 features as a consequence
- B. any switch that supports PoE, LLDP-MED and Flow Control
- C. multi-Layer refers specifically to using chassis switches with several line cards over stack port switches
- D. has all the functionality of a Layer 2 switch and most of the functionality of a Layer 3 router
Answer: D
NEW QUESTION 29
What are two features of the three-tier designs? (Choose two.)
- A. a more scalable design over by leveraging a distribution layer to handle Layer 3 routing and access control in large deployments
- B. removes the distribution layer in favor of a spine-leaf design used in modern data center deployments
- C. uses only Layer 2 access on the Access and the Core with Layer 3 routing and access control provided at the distribution layer
- D. is considered legacy by requiring a large flat layer-two broadcast domain from Core to Access and should be avoided
- E. adds a distribution layer to free up resources from the Core for improved performance and routing throughput
Answer: A,E
NEW QUESTION 30
Which Ethernet port combination does the Aruba 5400R ZL2 switch series support?
- A. 10/100 Megabit Ethernet, Gigabit Ethernet, and 100 Gigabit Ethernet
- B. Gigabit Ethernet, 25 Gigabit Ethernet, and 40 Gigabit Ethernet
- C. 10/100 Megabit Ethernet, Gigabit Ethernet, and 40 Gigabit Ethernet
- D. 10/100 Megabit Ethernet, Gigabit Ethernet, 25 Gigabit Ethernet, and 100 Gigabit Ethernet
Answer: C
NEW QUESTION 31
Match the available stacking feature to the correct AOS-CX switch model. Stacking features may be used more than once.
Answer:
Explanation:
NEW QUESTION 32
Refer to the exhibit.
The command show LLDP neighbor-info gets typed into Access-1. All switches are Aruba OS-CX switches. What is the output of this command?
- A. Option A
- B. Option D
- C. Option B
- D. Option C
Answer: B
NEW QUESTION 33
The section in blue can be ignored.
SW1(config)# interface 1/1/1-1/1/2
SW1(config-if-<1/1/1-1/1/2)# vlan access 2
SW1(config-if-<1/1/1-1/1/2)# exit
SW1(config)# interface 1/1/11-1/1/17
SW1(config-if-<1/1/11-1/1/17)# vlan access 17
SW1(config-if-<1/1/11-1/1/17)# exit
After completing the above commands, what is the expected output of show vlan with no other vlan commanded having been added?
- A.
- B.
- C.
- D.
Answer: C
NEW QUESTION 34
......
Best way to practice test for HP HPE6-A72: https://www.vcedumps.com/HPE6-A72-examcollection.html
HPE6-A72 Dump Ready - Exam Questions and Answers: https://drive.google.com/open?id=1KYy7JS6DhdwYXKoZiTmTDmmhbcMQemqK
